Goldbull board Topic is solved

Use this forum for requesting small changes in ChibiOS. Large changes should be discussed in the development forum. This forum is NOT for support.
Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Goldbull board  Topic is solved

Postby Eddie » Fri Nov 24, 2017 10:36 am

Hi,
I bought this interesting board.

http://www.hotmcu.com/stm32f107vct6-dev ... p-114.html

I made board files and a demo project. Can it be included in the repository?
Files in Attachment.
Attachments
RT-STM32F107-GOLDBULL_F107-LWIP-FATFS-USB.ZIP
(30.66 KiB) Downloaded 162 times
GOLDBULL_STM32_F107VC.ZIP
(3.68 KiB) Downloaded 169 times

User avatar
Giovanni
Site Admin
Posts: 14444
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 1074 times
Been thanked: 921 times
Contact:

Re: Goldbull board

Postby Giovanni » Fri Nov 24, 2017 10:39 am

Hi,

Could you try to not have a separate demo? in trunk there is an "unified" demo that you could use: RT-STM32-LWIP-FATFS-USB. You need to add the makefile and the configuration files, follow the pattern.

I am trying to reduce the total number of projects in the distribution, most of them are clones with little changes.

Giovanni

Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Re: Goldbull board

Postby Eddie » Fri Nov 24, 2017 10:44 am

Ok, I will try to create a unified demo.

Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Re: Goldbull board

Postby Eddie » Fri Nov 24, 2017 11:04 am

I was looking at a unified demo and I see the little problem. Unified demo uses SDC driver, GoldBull needs MMC driver. This will require a change in the main program.
Or you have any other suggestions.

Eddie

User avatar
Giovanni
Site Admin
Posts: 14444
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 1074 times
Been thanked: 921 times
Contact:

Re: Goldbull board

Postby Giovanni » Fri Nov 24, 2017 11:09 am

hi,

You could put the driver initialization in a conditional block depending if HAL_USE_SDC is enabled or not.

Giovanni

Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Re: Goldbull board

Postby Eddie » Fri Nov 24, 2017 5:10 pm

ok, unified demo created..
Tested on Olimex E407 and Goldbull F107 :)
Attachments
RT-STM32-LWIP-FATFS-USB.ZIP
(61.42 KiB) Downloaded 163 times

User avatar
Giovanni
Site Admin
Posts: 14444
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 1074 times
Been thanked: 921 times
Contact:

Re: Goldbull board

Postby Giovanni » Fri Dec 01, 2017 10:19 am

Hi,

Code merged with few changes, I cannot test on the goldbull board however.

Giovanni

Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Re: Goldbull board

Postby Eddie » Fri Dec 01, 2017 1:44 pm

I test the goldbull in the afternoon and write the result.

Eddie

Eddie
Posts: 44
Joined: Sat Mar 16, 2013 5:57 pm
Location: Czech Republic
Has thanked: 2 times
Been thanked: 6 times

Re: Goldbull board

Postby Eddie » Fri Dec 01, 2017 4:21 pm

Hi,
demo for Goldbull working without problems :)

Eddie


Return to “Small Change Requests”

Who is online

Users browsing this forum: No registered users and 9 guests