STM32F1 CAN RX Interrupt

ChibiOS public support forum for topics related to the STMicroelectronics STM32 family of micro-controllers.

Moderators: RoccoMarco, barthess

ubis
Posts: 1
Joined: Sun Sep 10, 2017 8:23 am

STM32F1 CAN RX Interrupt

Postby ubis » Sun Sep 10, 2017 8:52 am

Hello,
I'm trying to to use RX0 interrupt service on STM32F103C8T6 MCU.

I've got the following code:

Code: Select all

#include <stdio.h>
#include <string.h>

#include "ch.h"
#include "hal.h"
#include "board.h"
#include "chprintf.h"

#include "def.h"

CANRxFrame   txmsg;
SerialConfig uartCfg = { .speed = SERIAL_BAUDRATE };
CANConfig    cancfg  = { .mcr = CAN_MCR_ABOM | CAN_MCR_AWUM };

void SetBaudRate(int baud);

int main(void) {
   // system initialization
   halInit();
   chSysInit();

   // enable IRQ vector
   nvicEnableVector(CAN1_RX0_IRQn, CORTEX_PRIO_MASK(STM32_CAN_CAN1_IRQ_PRIORITY));

   // set pins
   palSetPadMode(GPIOA, 11, PAL_MODE_INPUT_PULLUP);               // CAN RX
   palSetPadMode(GPIOA, 12, PAL_MODE_STM32_ALTERNATE_PUSHPULL);   // CAN TX

   // serial initialization
   sdStart(&SD1, &uartCfg);
   PRINT("\r\n\n");
   PRINT("Running serial console at %d\r\n", SERIAL_BAUDRATE);

   SetBaudRate(250000);          // set can bus baud rate
   canStart(&CAND1, &cancfg);      // start can bus

   while (true) {
      /*msg_t t = canReceive(&CAND1, CAN_ANY_MAILBOX, &txmsg, TIME_IMMEDIATE);
      if (t == MSG_OK) {
         PRINT("received\r\n");
      }*/
      chThdSleepMilliseconds(100);
   }
}

void SetBaudRate(int baud) {
   int tmp  = 2000000 / baud - 1;
   cancfg.btr  = CAN_BTR_SJW(3);
   cancfg.btr |= CAN_BTR_TS1(11);
   cancfg.btr |= CAN_BTR_TS2(4);
   cancfg.btr |= CAN_BTR_BRP(tmp);
}

CH_IRQ_HANDLER(CAN1_RX0_IRQHandler) {
CH_IRQ_PROLOGUE();

   chSysLockFromISR();
   msg_t t = canReceive(&CAND1, CAN_ANY_MAILBOX, &txmsg, TIME_IMMEDIATE);
   if (t == MSG_OK) {
      PRINT("interrupt received\r\n");
   }
   chSysUnlockFromISR();

CH_IRQ_EPILOGUE();
}


I think i'm missing something. It doesn't trigger the interrupt.
However, if I use

Code: Select all

canReceive
in main loop cycle, it does receive CAN message.

Also PRINT is just a definition to chprintf.
It could be overhead to use chprintf in interrupt, so even setting pin to different state doesn't work.

User avatar
Giovanni
Site Admin
Posts: 14444
Joined: Wed May 27, 2009 8:48 am
Location: Salerno, Italy
Has thanked: 1074 times
Been thanked: 921 times
Contact:

Re: STM32F1 CAN RX Interrupt

Postby Giovanni » Sun Sep 10, 2017 10:26 am

Hi,

ChibiOS drivers enable interrupts and define interrupt vectors internally, there is no need for you to do that. If you want to access CAN at register level then you need to disable the CAN driver or there would be 2 ISRs for the same vector.

Giovanni


Return to “STM32 Support”

Who is online

Users browsing this forum: No registered users and 10 guests